Skip to product information
1 of 18

OGSolarStore

Insulated Flexible Copper Busbar for Battery Packs, 150A to 350A Continuous

Insulated Flexible Copper Busbar for Battery Packs, 150A to 350A Continuous

Available to order Ships in 1–2 weeks.

Regular price $15.00 CAD
Regular price Sale price $15.00 CAD
Sale Sold out
Size
Hole to Hole Length (inches)
Quantity
  • Cut to order in Michigan
  • Material sourced from industry-certified supplier
  • Ships in 3-5 business days

Insulated flexible copper busbars for connecting your battery pack to the rest of the system. Use them anywhere a cable with two lugs would go: pack terminals to a fuse or breaker, shunt to BMS, BMS to bus bar, battery to inverter, or between battery boxes and modules. They are not meant for cell-to-cell series connections inside the pack.

Compared to cable, there are no lugs to crimp. The bar is punched and bolted directly, it bends and twists by hand to fit tight layouts, and it takes less room than the equivalent wire. The tinned copper resists corrosion and the halogen-free insulation is rated to 1500 VDC.

Each piece is cut and punched to order in Ann Arbor, Michigan.

How to pick a size. Pick by continuous current: the steady load your system draws for 30 minutes or more. The max rating is for short bursts only, so don't size to it. Replacing cable? The 150A size is about like 4 AWG, the 250A size like 1/0, and the 350A size like 4/0.

Which size do I need? The flexible busbar size chooser takes your continuous current, air temperature, what the bar bolts to and how the bars are laid out, then picks the smallest size that fits.

Specifications

  • 150A continuous size (200A max)
    • 150A continuous, 200A max
    • Copper: 15.5 x 1.6 mm (24.8 mm², 49 kcmil, between 4 and 3 AWG)
    • M6 mounting holes (6.35 mm, fits M6 screws; a 1/4-20 screw will not pass reliably)
  • 250A continuous size (350A max)
    • 250A continuous, 350A max
    • Copper: 24 x 2 mm (48 mm², 95 kcmil, between 1 AWG and 1/0)
    • M8 / 5/16 in mounting holes (M10 / 3/8 in on request)
  • 350A continuous size (500A max)
    • 350A continuous, 500A max
    • Copper: 24 x 4 mm (96 mm², 190 kcmil, between 3/0 and 4/0 AWG)
    • M8 / 5/16 in mounting holes (M10 / 3/8 in on request)
    • Made to order: ships in 5 to 7 business days
  • Lengths: 2 to 12 in, measured hole center to hole center. Overall length is 1 in longer (0.5 in past each hole).

Current rating vs. installation

The max rating is for short loads (minutes, not hours). For continuous loads (30 minutes or more), the safe current depends on how hot the air around the bar gets and what it bolts to. Use the "fuse, breaker or lug" rows for runs to those parts. Use the "cell terminal" rows when the bar bolts straight onto a cell, because cell terminals should stay under 60°C. One bar, on edge, rounded down to the nearest 5 A.

Where the bar runs Ends on 150A size 250A size 350A size
Open rack, room at 25°C Fuse, breaker or lug 200A 325A 475A
Open rack, room at 25°C Cell terminal 165A 270A 390A
Closed battery box, 40°C inside Fuse, breaker or lug 165A 270A 390A
Closed battery box, 40°C inside Cell terminal 120A 200A 290A

Hot shed or garage, bars side by side or stacked, or bars lying flat? The size chooser works those out for you. Loose or dirty joints run hotter, so keep every bolted joint clean and torqued.

Disclaimer: For reference only. Do proper engineering to determine your requirements and always follow applicable code.

Technical details

  • Conductor: electrolytic tinned copper (Cu-ETP)
  • Insulation: TPE, low smoke, halogen-free, flame retardant
  • Self-extinguishing: UL 94 V0
  • Insulation elongation: 500%
  • Dielectric strength: 20 kV/mm
  • Nominal voltage: 1000 VAC / 1500 VDC (IEC/UL)
  • Temperature range: -50°C to +115°C
  • Insulation thickness: 1.8 mm typical

Datasheet

Custom orders

Need a length that isn't listed, a different hole size, or more than two holes? Send us a message with what you need and we will quote it.

Contact us for your custom order

View full details